Normal Boot Capture from FFx30 Series Faxfinder

Normal complete Boot capture of FaxFinder using Firmware version 2.0.4

The purpose of this capture is to allow Multitech technical support a point of reference for comparison against a boot log of FaxFinder which is not booting normally. This may provide insight into what is causing FaxFinder with issue not to boot normally and saves the time of having to run boot capture of functional FaxFinder.

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
START OF BOOT CAPTURE
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx


+Ethernet eth0: MAC address 00:08:00:72:30:90
IP: 192.168.2.1/255.255.255.0, Gateway: 192.168.2.1
Default server: 192.168.2.2, DNS server IP: 192.168.11.251

RedBoot(tm) bootstrap and debug environment [ROM]
Red Hat certified release, version 1.94 - built 13:04:27, Mar 18 2008

Platform: IXDPG425 Development Platform (XScale) BE
Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.

RAM: 0x00000000-0x08000000, 0x0001f158-0x07fd0000 available
FLASH: 0x50000000 - 0x51000000, 128 blocks of 0x00020000 bytes each.
== Executing boot script in 3.000 seconds - enter ^C to abort
RedBoot> fis load image
RedBoot> go -n 0x00700000
Uncompressing Linux........................................................... done, booting the kernel.
Linux version 2.4.27-uc1 (jjg@jjg-linux) (gcc version 3.3.6) #2 Tue Oct 20 11:14:52 CDT 2009
CPU: XScale-IXP4xx/IXC11xx revision 2
Machine: Intel IXP425 Monte Jade Demonstration Platform
Warning: bad configuration page, trying to continue
alloc_bootmem_low
memtable_init
On node 0 totalpages: 32768
zone(0): 16384 pages.
zone(1): 16384 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0,115200 root=/dev/ram0 initrd=0x00800000,10747k mem=128M@0x00000000 ramdisk_size=32768
Calibrating delay loop... 548.86 BogoMIPS
Memory: 128MB = 128MB total
Memory: 116896KB available (1451K code, 291K data, 232K init)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
POSIX conformance testing by UNIFIX
PCI: reset bus...
PCI Autoconfig: Found Bus 0, Device 13, Function 0
PCI Autoconfig: BAR 0, Mem, size=0x400, address=0x4bfffc00
PCI: bus0: Fast back to back transfers enabled
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xff000003 (irq = 15) is a XScale UART
ttyS01 at 0xff001003 (irq = 13) is a XScale UART
ledman: Copyright (C) SnapGear, 2000-2003.
LED: registered reset button on IRQ29
DS1302: Copyright (C) 2001, Greg Ungerer (gerg@snapgear.com)
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
PPP generic driver version 2.4.2
PPP MPPE compression module registered
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
cfi_cmdset_0001: Erase suspend on write enabled
Using buffer write method
LOOK for RedBoot RedBoot
Creating 7 MTD partitions on "IXP425 Flash":
0x00000000-0x00040000 : "RedBoot"
0x00040000-0x00180000 : "config"
0x00180000-0x00cc0000 : "image"
0x00180000-0x00280000 : "zImage"
0x00280000-0x00cc0000 : "ramdisk"
0x00fc0000-0x00fc1000 : "RedBoot config"
mtd: partition "RedBoot config" doesn't end on an erase block -- force read-only
0x00fe0000-0x01000000 : "FIS directory"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
lec.c: Oct 20 2009 10:51:42 initialized
mts_cf: initializing...
mts_cf: device found
Partition check:
cfa: cfa1
mts_cf: loaded successfully
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 10747K
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 232K
init started: BusyBox v1.00 (2009.10.20-15:55+0000) multi-call binary
init started: BusyBox v1.00 (2009.10.20-15:55+0000) multi-call binary
Starting pid 10, console : '/bin/sh'
mount: /etc/mtab: Read-only file system
Using /lib/modules/2.4.27-uc1/kernel/ixp425/ixp400/ixp400.o
Module init.
Using /lib/modules/2.4.27-uc1/kernel/ixp425/net/ixp425_eth.o
ixp425_eth:
Initializing IXP425 NPE Ethernet driver software v. 9.1
ixp425_eth: Initialising Queue Manager...
valid PHY ID
valid PHY ID
physcan
ixp425_eth: Found PHY 0 at 0
ixp425_eth: Found PHY 1 at 1
ixp425_eth: Configuring PHY 0
ixp425_eth: Configuring PHY 1
ixp425_eth: eth0 is using the PHY at address 0
ixp425_eth: eth1 is using the PHY at address 1
Set eth0 to MAC address 00:08:00:72:30:90
Creating /dev/ttyMU1a
Creating /dev/ttyMU1b
Model of last device: FF230
Multi-Tech ISIUPCI 1/2/4/8 port serial driver version 2.06 (2009-10-19) with SHARE_IRQ SERIAL_PCI enabled
SIOCDELRT: No such process
e2fsck 1.25 (20-Sep-2001)
mts: clean, 1477/248832 files, 115754/1990295 blocks
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on cf(252,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
qmail setup is not needed
crond[56]: crond 2.3.2 dillon, started, log level 8

Starting pid 60, console : '/sbin/klogd'
Starting pid 61, console : '/sbin/syslogd'
Starting pid 62, console : '/bin/inetd'
Starting pid 63, console : '/bin/slogrot'
Starting pid 64, console : '/usr/local/sbin/cupsd'
Starting pid 65, console : '/bin/mefax'
Starting pid 66, console : '/bin/resetd'
Starting pid 67, console : '/usr/ffweb/ffweb'
Starting pid 69, console : '/bin/bash'
# INFO: Og uses the Sqlite store.

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
END OF BOOT CAPTURE
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx