CallFinder® GSM Resolutions

Updated: 06/28/2011 04:46:10 PM

Does the CallFinder use a standard SMA antenna connector

Product: CF100FX2-G

Updated: 03/16/2009 02:55:41 PM

What is the ring voltage provided by the CallFinder What is the ringer equivalent number (REN)

Product: CF100FX2-G

Updated: 03/16/2009 02:53:23 PM

I receive an error every time I issue the command AT+CREG

Product: CF100FX2-G

Updated: 02/03/2009 02:55:49 PM

What Serial speed do I use for terminal software (console port)

Products: CF100FX2-G,CF100FX2-C

Updated: 02/02/2009 04:58:57 PM

Voice calls work great through the GSM callfinder, but faxing won't work.

Product: CF100FX2-G

Updated: 12/11/2008 01:42:47 PM

How much current does this unit draw when in an idle state and when making a call

Product: CF100FX2-G

Updated: 12/11/2008 01:42:28 PM

Do these operate at 2.4 GHz

Product: CF100FX2-G

Updated: 07/15/2008 02:52:12 PM

An analog device (PBX, etc) attached to the CallFinder does not reliably detect dtmf digits received from the GSM network.

Products: CF100FX2-G,CF100FX2-G

Updated: 07/01/2008 10:56:23 AM

I want to activate the CallFinder with Sprint, what steps do I take to get it working

Products: CF100FX2-C,CF100FX2-C

Updated: 01/21/2008 04:49:01 PM

Does your CallFinder Gateway route calls by using cell towers

Products: CF100FX2,CF100FX2-G,CF100FX2-C

Updated: 12/13/2007 08:50:32 AM

Will the CallFinder work with Sprint

Product: CF100FX2-C

Updated: 10/22/2007 03:37:47 PM

Does the CallFinder GSM work with every sim card that is inserted into it

Product: CF100FX2-G

Updated: 10/05/2007 02:41:45 PM

The CallFinder is FXS on a line port of our phone system. Voice volume is low on both sides, regardless of which side originates the call.

Products: CF100FX2-G,CF100FX2-C

Updated: 09/20/2007 07:53:44 AM

What is line reversal

Products: CF100FX2-G,CF100FX2-C

Updated: 09/05/2007 11:50:53 AM

Calls not disconnecting on PBX side (with voice mail use).

Products: CF100FX2-G,CF100FX2-C

Updated: 08/02/2007 11:22:03 AM

Should AT commands work in data mode even if it's not activated

Products: CF100FX2-G,CF100FX2-C

Updated: 08/02/2007 02:52:33 PM

Can I use this for a modem and get Internet access

Products: CF100FX2-G,CF100FX2-C

Updated: 07/31/2007 09:26:38 AM

Calls start on the cell side to the PBX which gets to voice mail, but when the call is ended on the cell side, the PBX never disconnects.

Products: CF100FX2-G,CF100FX2-C

Updated: 07/25/2007 03:44:20 PM

I'm unable to activate the CF100FX2-C to Verizon.

Product: CF100FX2-C

Updated: 07/23/2007 03:35:29 PM

Is there a pre-defined loop-open disconnect for that device

Products: CF100FX2,CF100FX2-G,CF100FX2-C

Updated: 07/10/2007 03:09:03 PM

Can I use the CallFinder GSM with a dialer as if it is a regular phone line with a dialtone. I will have it at a remote location that doesn't have phonelines.

Products: CF100FX2-G,CF100FX2-C

Updated: 03/15/2007 07:41:16 AM

Fixed - An AT command processing problem. Depending on what is happening on the cellular side, (i.e. signal strength adjusting or call being received), the OK would be received, but the parameter would not be changed.

Products: CF100FX2,CF100FX2-G,CF100FX2-C

Updated: 03/15/2007 07:45:32 AM

Added - An auto dial feature on the FXO port.

Products: CF100FX2,CF100FX2-G,CF100FX2-C

Updated: 03/15/2007 07:44:54 AM

Changed - The cadence of the ring signal to 2 sec on / 4 sec off.

Products: CF100FX2,CF100FX2-G,CF100FX2-C

Updated: 03/15/2007 07:42:03 AM

Increased the ring signal on the FXS port.

Products: CF100FX2,CF100FX2-G,CF100FX2-C

Updated: 01/11/2007 11:48:03 AM

Can the Callfinder GSM/CDMA be dialed into its FXO port and have a certain number auto called to the cellular service.

Product: CF100FX2