|
Firmware
| File |
Version |
Size |
|
| mtasr305.exe |
3.05 |
2,407,027 bytes |
- File Contents: Router Firmware3
This file contains router firmware for the 8-Meg* versions of the router models listed below.
* 8-meg router has two (4-meg) memory SIMMs
|
- Models: MTASR1-100, MTASR2-201, MTASR3
|
|
| mtr-221.exe |
2.21 |
1,746,734 bytes |
- File Contents: Router Firmware2
This file contains Router firmware and an update utility for the 4-Meg* versions of the MTASR1-100 and MTASR3 routers.
* 4-meg router has one (4-meg) memory SIMM
|
- Models: MTASR1-100, MTASR3
|
|
| rf1-220.exe |
2.20a |
1,683,381 bytes |
- File Contents: Router Firmware1
This file contains router firmware and an update utility for the 2-Meg* MTASR1-100 models.
-
* 2-meg router has two (1-meg) memory SIMMs.
|
- Model: MTASR1-100
|
|
| rf200-4m.exe |
2.21 |
1,708,046 bytes |
- File Contents: Router Firmware1
This file contains router firmware and an update utility for 4-meg* MTASR1-200 models.
-
* 4-meg MTASR1-200 has one (4-meg) memory SIMM.
|
- Model: MTASR1-200
|
|
| rf2-220.exe |
2.20a |
1,651,699 bytes |
- File Contents: Router Firmware1
This file contains router firmware and an update utility for 2-meg* MTASR1-200 models.
-
* 2-meg MTASR1-200 has two (1-meg) memory SIMMs.
|
- Model: MTASR1-200
|
|
| rf802ew_v730_v458.exe |
7.30 / 4.58 |
11,188,230 bytes |
- File Contents: Install Software/Firmware 1
This file contains software and firmware for installing model RF802EW.
A README file is available and contains the release notes on this product.
|
- Model: RF802EW
|
|
| rft1-303.exe |
3.03 |
2,691,079 bytes |
- File Contents: Router Firmware1
This file contains firmware and an update utility for 8-meg* MTASR2-203 router with internal T1 DSU.
* 8-meg router has two (4-meg) memory SIMMs.
|
- Model: MTASR2-203
|
|
| rfxx0vpn_334 |
3.34 |
1,000 bytes |
- File Contents: Live Update!12
- Revised: May, 2008
-
NOTE: If you are currently running 3.32 or below and you are using URL content filter license, DO NOT perform live update until your URL content license is expired. Your old URL license key will NOT work in the new 3.34 update.
NOTE: if you are using PPPoE and VPN, after you perform live update to 3.34, your VPN will stop working. Please contact tech support support@multitech.com in order to correct this problem.
-
In order to perform a live update to the latest firmware Version 3.3x, your RouteFinder™ must be running the newer version of a 3.25 release. To check if your RouteFinder is running the correct version of 3.25, webadmin into the RouteFinder and under Administration --> System Setup, there should be a box with a header showing "System Logging". If it is showing "Remote Syslog", you have the an older version of 3.25. Therefore, you must reinstall using the newer version of 3.25 before you can perform the live update.
-
Please contact our Tech Support Department if you need to reinstall with the newer version of 3.25 software.
In order to run Version 3.3x, and if you are planning to use URL content filtering, you MUST have a minimum of 256MB of memory. Some older RF600VPN hardware with serial numbers lower than 9337635 CANNOT be upgraded due to the hardware limitation. RF660VPN hardware support only a maximum of 256MB of memory. RF600VPN uses a standard PC133 memory module; RF660VPN uses a standard PC100 memory module; RF760VPN, RF850 and RF860 use a standard DDR memory module.
Installation note: This README contains how to run live update and release notes for the products.
|
- Models: RF600VPN, RF600VPN-EU, RF660VPN, RF660VPN-EU, RF760VPN, RF760VPN-EU, RF850, RF850-EU, RF850-GB/IE, RF860, RF860-EU, RF860-GB/IE
|
|
|
|
